Progress Thread She’s a runner

90sickfox · Feb 1, 2021

I meet a new hood too. I've been fixing stress cracks and stuff on my current hood for the last 15 years. I just can't bearing myself to spend the money on one. I remember when you could get one new for 300 bucks.

KZGUNS · Feb 1, 2021

90sickfox said:
I meet a new hood too. I've been fixing stress cracks and stuff on my current hood for the last 15 years. I just can't bearing myself to spend the money on one. I remember when you could get one new for 300 bucks.

Ya there’s still some cheap ones out there but I didn’t want fittment issues or a flimsy hood so I decided to bite the bullet and get the cervini

KZGUNS · Feb 9, 2021

Hood came in yesterday. Had to set it on the car and see how it looked. I ordered aero catch hood pins so I guess I’ll install those once I get everything aligned
I also have the original headlights so I’m gonna polish the lenses and put those in.

Steel1 · Feb 9, 2021

Looks good.
How big of a cowl 3-4" ?
Going to paint it yourself ?

KZGUNS · Feb 9, 2021

Steel1 said:
Looks good.
How big of a cowl 3-4" ?
Going to paint it yourself ?

2.5” I’ll have a buddy of mine paint it or actually he’ll help me, I’ll prime it and block it. He’ll give me some time behind the gun so I can learn a little. I’ll cut and buff it myself

KZGUNS · Feb 11, 2021

Got the aerocatch pins installed. Wasn’t nearly as bad as I thought it would be. On the backside I clearances only what was needed so if there was room to slide the retaining ring between the two panels I did.

KZGUNS · Feb 28, 2021

Question for tko users. So stifflers crossmember with their tko install kit give you spacers to raise the back of the trans like an inch. Well that pushes the trans into the tunnel. I’m considering turning those spacers down an 1/8-1/4” how did you guys handle this? @90sickfox did you have this issue

Monkeybutt2000 · Feb 28, 2021

KZGUNS said:
Question for tko users. So stifflers crossmember with their tko install kit give you spacers to raise the back of the trans like an inch. Well that pushes the trans into the tunnel. I’m considering turning those spacers down an 1/8-1/4” how did you guys handle this? @90sickfox did you have this issue

BFH

KZGUNS · Feb 28, 2021

Monkeybutt2000 said:
BFH

Well ya that’s an option LOL. I may end up doing that

Monkeybutt2000 · Feb 28, 2021

KZGUNS said:
Well ya that’s an option LOL. I may end up doing that

My TKO maybe sits about an inch away from the tunnel. I'll eventually go to the Stifflers unit,but unsure if the spacer kit will work or not,trial and error I guess.

KZGUNS · Feb 28, 2021

I ended up just turning .100 off the spacers and it’s now not touching the tunnel. It was touching the rib right behind the shifter cutout. I reworked the H pipe and added cats. Don’t mind the crappy looking welds my neighbors breaker kept tripping. I’m ordering new tail pipes to clean up the previous owners work... once I get those I can roll it back home and finish up the cooling system etc.

90sickfox · Mar 1, 2021

Mine hit right in front if the shifter. There was a support rib there. I just took a hammer and moved it out of the way.

KZGUNS · Mar 7, 2021

Clutch cable question. I have a non adjustable cable and had to turn the adjuster almost all the way out to get the slack out. Anybody have this issue?

Monkeybutt2000 · Mar 7, 2021

KZGUNS said:
Clutch cable question. I have a non adjustable cable and had to turn the adjuster almost all the way out to get the slack out. Anybody have this issue?

Mine was similar, do you have the MM cable?

KZGUNS · Mar 7, 2021

Monkeybutt2000 said:
Mine was similar, do you have the MM cable?

I don’t think it’s an mm cable. It is the non adjustable type like factory. What did you end up doing

90sickfox · Mar 7, 2021

Are you using a steel bellhousing ? If you are there needs to be a spacer where the cable housing Mets the bellhousing. It'll take out the slack. If not you need a double hook quadrant so you can move the cable at the pedal to remove slack.

I run a tko600 with aluminum bell, firewall adjuster, double hook quadrant, and stock cable.

KZGUNS · Mar 7, 2021

90sickfox said:
Are you using a steel bellhousing ? If you are there needs to be a spacer where the cable housing Mets the bellhousing. It'll take out the slack. If not you need a double hook quadrant so you can move the cable at the pedal to remove slack.

I run a tko600 with aluminum bell, firewall adjuster, double hook quadrant, and stock cable.

I have an aluminum bell. I do already have a double hook quadrant installed when I did the adjuster a while back. I’ll crawl under the dash and move the cable. Thanks for the help!!!

KZGUNS · Mar 11, 2021

For the two of you paying attention to my progress I have the car back home. Tranny, exhaust etc all done. I’m currently working through all the little stuff. I’m hoping to be ready for first fire by the end of the month.

a91what · Mar 11, 2021

Three of us

stanglx2002 · Mar 11, 2021

Four

Progress Thread She’s a runner

Wasn't a pretty sight...and I've got big hands

I can swing up to 11”

I can swing up to 11”

Attachments

Mustang Master

I can swing up to 11”

I can swing up to 11”

Attachments

I can swing up to 11”

Mustang Master

I can swing up to 11”

Mustang Master

I can swing up to 11”

Attachments

Wasn't a pretty sight...and I've got big hands

I can swing up to 11”

Mustang Master

I can swing up to 11”

Wasn't a pretty sight...and I've got big hands

I can swing up to 11”

I can swing up to 11”

SendMeUrDataLog

CT Material here

Similar threads

Privacy & Transparency

Privacy & Transparency