Progress Thread Tannerc91gt’s Build(s) Thread
- Thread starter tannerc91gt
- Start date
Recently ran into a Turbo Camaro guy with fender exit exhaust-he was rocking these tiny race bullet mufflers-slip fit style-with them off there was a noticeable difference.
I was surprised lol
Figured I’d mention just in case you need a slight silencer down the road
https://www.summitracing.com/parts/wlk-24249
I was surprised lol
Figured I’d mention just in case you need a slight silencer down the road
https://www.summitracing.com/parts/wlk-24249
Took over a week to get the cam swap mostly finished. Still need to hammer down the oil pan bolts and put the accessories back on.
Went ahead and tore into the pickup tube/pan setup trying to hunt down my oil pressure issues.
No pinched o ring but I did find the pickup tube bolt down tab was contacting the windage tray and not fully seating so I think pan/pickup clearance could have been a hair tight. Also redrilled the motor mounts and moved the motor back 1”. Will have to redo the trans mount tabs again but driveshaft engagement is better and it gave the turbo some breathing room so I’ll call it a win.
Then I decided I’d go ahead and throw a new timing chain and dampener on while I had the front of the motor apart. Easily distracted as usual.
It’s buttoned up enough to let it go back to sitting for a while
Went ahead and tore into the pickup tube/pan setup trying to hunt down my oil pressure issues.
No pinched o ring but I did find the pickup tube bolt down tab was contacting the windage tray and not fully seating so I think pan/pickup clearance could have been a hair tight. Also redrilled the motor mounts and moved the motor back 1”. Will have to redo the trans mount tabs again but driveshaft engagement is better and it gave the turbo some breathing room so I’ll call it a win.
Then I decided I’d go ahead and throw a new timing chain and dampener on while I had the front of the motor apart. Easily distracted as usual.
It’s buttoned up enough to let it go back to sitting for a while
Damn fine thread. Just finished 75 pages. I have taken my original build thread car (over on Corral) and decided it had gotten out of hand as well for the chassis it is. So I did as you did, bought another car to build into more track oriented race car that can be driven on the street.
Reading through yours, I find tons of stuff I am already looking at. Like the solid state disconnect setup (with dual switches), the Leash Street/Strip board, and what looks like is the wiring harness kit from https://precisionfabandwire.com/main.sc , narrowed rear (mine is 48' flange to flange) with Billet Specialities 15x12 & 5.5bs though, on board air system, and other stuff.
Once I get my car out of the chassis shop, and I can get home to work on it I may need to start a build thread over here instead. Corral is dead!
Reading through yours, I find tons of stuff I am already looking at. Like the solid state disconnect setup (with dual switches), the Leash Street/Strip board, and what looks like is the wiring harness kit from https://precisionfabandwire.com/main.sc , narrowed rear (mine is 48' flange to flange) with Billet Specialities 15x12 & 5.5bs though, on board air system, and other stuff.
Once I get my car out of the chassis shop, and I can get home to work on it I may need to start a build thread over here instead. Corral is dead!
Sounds like a build I’d like to check out.
This forum really is the last of a dying breed unfortunately
Got the new end tank welded up on the intercooler. Also got the motor buttoned back up and the turbo kit bolted back on as well as the first coldside bend welded together.
Even had a visitor come out and check on the progress
Even had a visitor come out and check on the progress
I wasn’t alone today though. As you can see, he wasn’t much help but it made for a good morning
I'm reading through your thread, and of everything I've seen, this was the most impressive. I have yet to pull something like this off with my offspring. Kudos, good sir.
It was a fluke I think lol. You don’t realize how loud car building is until there’s a baby present
Coldside done other than making mounting tabs for the intercooler
Intercooler mounted, bungs welded in for a couple IAT sensors and a boost reference. Got the coldside painted up and fitted. Also got the boost controller plumbed. Thinking i can retire the welder for the rest of this deal.
Man, all I did was fix my lawn mower!
it needs a shift knob that says f'n fast to keep me motivated to mow too!
it needs a shift knob that says f'n fast to keep me motivated to mow too!
- Jul 12, 2017
- 2,474
- 1,348
- 173
Plumbed the BOVs (which worked out in a way that pleases whatever mental disorder I have). Ran the front brake lines and the return fuel line, FPR reference line, and a few other odds and ends.
Pretty good work for a weekend
Pretty good work for a weekend
It’s under the work bench in a box
Man I love this project. It looks so damn clean. Great work man, cant wait to see it driving.
I’ve got a car show sept 1 I’m dead set on making it to. Just a matter of whether it’s driven or trailered. Don’t usually care about car shows but it’s helped a ton to have something to shoot for
