Build Thread My Never Ending 89 Notch Thread

#4,621
So last nights progress . Made all the sensor connections at the Holley . Also made and additional 12v sensor out and ground sensor out from the Holley I’d I ever needed to add anything else . I have no reason for a 5v but if I ever do I’ll make one too . So now I have the trans brake input for the 2 step , trans temp sensor wired , drive shaft speed sensor pig tail ready to go .

The premise is eventually when I do the Holley dash or a race pak I can use the DSS to get a speedo . Also use it to calculate converter slip , oh and maybe some traction control .

Also made the harness for the meth kit . Right as I ran out of tape . Lol

 
Reactions: 2 users
#4,624
So the meth controller didn’t fit in the little info center at the right corner of the bezel that goes around the cluster it was hitting and I just wasn’t happy with it. So I came up with this tonight .

The cuts aren’t perfect but I did the best I could . It’s down low so it should look pretty slick

 
Reactions: 2 users
#4,629
Well I got some more done . All wiring in the car is done . Interior is 3/4 re installed . Have to hole saw the console tomorrow for my usb charging port by the arm rest . Also on the pass side of the console where I’m going to put a pass through for the ecu usb connection.

Over drive button mounted .
Got the shifter cable hooked up . Box on the shifter

Wires done for the usb charger .

Shifter box on and just laid the upper part of the console in place to get an idea .

Eventually I need to re spray my quarter plastics and some other stuff . That can be a project for later

 
Reactions: 3 users
#4,633
Chuckman said:
this is such a simple thing, but im digging that bracket to keep the usb plugged in.

oh, and im starting to wish i had mounted my hp (and tcu) in that same spot
Click to expand...
Hey , motion raceworks sells that bracket to stop the common issue of breaking the usb . There is a guy who literally was swinging the ecu by it that sold me on it . Just peace of mind
 
#4,634
Took a little break from wiring tonight . Installed the lokar billet dipstick for the trans.

Put the trans back up and the stifflers mount back on and secured it .

Cleaned the fans , Radiatior, and polished up the end tanks + the reservior and installed it as well as the lower hose and 2 heater hoses .

 
Reactions: 2 users
#4,637

I just wanna thank you.....

Thank you for posting that pic of your trans dipstick tube, cause now I know that that leakin btch that I have ( Lokar) has a solution that they are offering. Mine uses two O rings, instead of that grommet looking thing...when will you use it, and when will you be filling the trans?
 
Reactions: 1 user
#4,638

Hopefully end of April ! Lol

I’ve used the other style on the glides in the race cars . This is for an AOD so I’m wondering if that’s why they use the grommet on this ? Not sure
 
#4,639
Split the Holley harness open today . Moved the fuel pressure sensor to reach the reg . Extended the manifold air temp harness , extended the oil pressure sensor to reach the log . Moved the iac harness around . Cut the Chrysler plug off and re pinned for gm iac. ( was using a ford before )




 
Reactions: 5 users
You must log in or register to reply here.

Similar threads

Progress Thread Dirty Water Racing 89 Notch Project
Replies
64
Views
10K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Flyboy60
F
JCBeaver's 1993 GT Coyote Swap "The Never-Ending Project"
Replies
182
Views
27K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
JCBeaver
Progress Thread '93 Kenne Bell Notch
Replies
296
Views
47K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
James V
Progress Thread 95 2-Top Cobra Build Thread- Never ending
Replies
776
Views
89K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Essn95
Progress Thread 2001 Bullitt #265 - Build Thread (LOTS OF PICS)
Replies
41
Views
10K
1996 - 2004 SN95 Mustang -General/Talk-
MineralMan
Menu
Log in
Register