Build Thread My Never Ending 89 Notch Thread

stanglx2002 · Mar 25, 2019

Where is @Noobz347 or @General karthief to comment on the oil feed contraption

General karthief · Mar 25, 2019

Oil feed contraction?
Yeah, ok. Let me think on that a while.

TOOLOW91 · Mar 26, 2019

stanglx2002 said:
Where is @Noobz347 or @General karthief to comment on the oil feed contraption

Much nicer then the pipe I had with the misc fittings to adapt it all . It will never be a trailer queen show car but I’m trying to pay attention to. Detail and have a car that can do a little bit of it all .

TOOLOW91 · Mar 26, 2019

So firewall grommet showed up which will house the meth controller vac line , new speed sensor and speedo gear , and the bumper hardware with the header panel . I love fresh hardware for parts.

TOOLOW91 · Mar 27, 2019

So much little stuff done tonight .

Made up the little harness for the 1/8 npt trans temp sensor .

Replaced the engine harness grommet in the fire wall . Installed a new automatic speedo cable in the fire wall where the clutch cable used to be to house the vac line for the meth controller .

Installed the hardware I got for the rad hold downs . Also installed a new hood prop which I’ll replace the bolt to match the rad hold downs now.

Re made and shortened the oil pressure gauge line using the same black woven line that will be used for everything.

Put the 90 on the power steering line so it runs similar to factory .

Replaced the leaky trans speed sensor and put the correct speedo gear for the aod on it

Replaced the meth nozzles with brand new 625s

Ran the line through the engine bay back to the trunk and added the 1 way check valve . Marked the intake pipe where I want to drill and tap and called it a night .

hoopty5.0 · Mar 27, 2019

OMGJUSTFIREITUPPPPPPPAAAAHHHHHHHH

Just kidding. Sort of.

These withdrawls are killing me!

TOOLOW91 · Mar 27, 2019

Ready to party . Also knocked the Vortech down to match covers and intake

General karthief · Mar 27, 2019

You must not be afraid of that three headed monster oil adapter cracking from engine vibration?

TOOLOW91 · Mar 27, 2019

General karthief said:
You must not be afraid of that three headed monster oil adapter cracking from engine vibration?

not even a little bit .

It had a piece of pipe on it with a multitude of adapters for the blower and gauge feed for years . Never an issue . It’s stainless steel

TOOLOW91 · Mar 28, 2019

Some more mock up

TOOLOW91 · Mar 28, 2019

Minus the missing items that’s basically what it will look like complete . Comments ? Thoughts ? I’m pretty happy with it

RaggedGT · Mar 28, 2019

One of those radiator covers Kevin (@95steedamustang ) makes would be pretty sweet. Lol
Engine bay looks gorgeous buddy- future goals right there
I’ve been around for the last 4 or so motor swaps,this one is my favorite

a91what · Mar 28, 2019

why change to the GM iac valve??

RangerJoe · Mar 28, 2019

Wasn't a fan of the black rivet in panels originally, but it actually works pretty well with your color scheme. Looks pretty good I think!

Joe

TOOLOW91 · Mar 28, 2019

RangerJoe said:
Wasn't a fan of the black rivet in panels originally, but it actually works pretty well with your color scheme. Looks pretty good I think!

Joe

It works for now I agree . Eventually it will be smooth and body color one day . Budget though so this is what it is . I agree though 1000 percent

TOOLOW91 · Mar 28, 2019

a91what said:
why change to the GM iac valve??

Ford eats up a output on my Holley . Tuner likes the gm iac and its built in the harness just swapped the plug .

TOOLOW91 · Mar 28, 2019

RaggedGT said:
One of those radiator covers Kevin (@95steedamustang ) makes would be pretty sweet. Lol
Engine bay looks gorgeous buddy- future goals right there
I’ve been around for the last 4 or so motor swaps,this one is my favorite

Thought about the rad cover just not in love with how it sits on the core support . I thought about literally just a cover to cover the top of the rad itself and finish it off.

TOOLOW91 · Mar 29, 2019

Tonight’s progress .

Mounted fuel pressure regulator now that I have the last fitting I was waiting on .

Re installed the bumper / header panel brackets now that they are powder coated

Mocked up gas tank and drilled out the front of the cover for the feed line .

Installed sending unit . Return line fitting in top of the tank . And -6 roll over valve .

Removed the old -6 return line . Starting running the new -10 feed line .

TOOLOW91 · Mar 29, 2019

After saving a few hundred on my pump because someone opened it and never used it they never sent the bracket it with it . So I ordered what I thought was right and it wasn’t . I want to get it mounted . So I cut the ears
Off . Re drilled it and boom

TOOLOW91 · Mar 30, 2019

Build Thread My Never Ending 89 Notch Thread

CT Material here

wonder how much it would cost to ship you a pair

If you're the village idiot what's that make me?

If you're the village idiot what's that make me?

If you're the village idiot what's that make me?

mechanicus terribilis

If you're the village idiot what's that make me?

wonder how much it would cost to ship you a pair

If you're the village idiot what's that make me?

If you're the village idiot what's that make me?

If you're the village idiot what's that make me?

Been here over a DECADE and still no CT

SendMeUrDataLog

I leave the horn on while driving

If you're the village idiot what's that make me?

If you're the village idiot what's that make me?

If you're the village idiot what's that make me?

If you're the village idiot what's that make me?

If you're the village idiot what's that make me?

If you're the village idiot what's that make me?

Similar threads

Privacy & Transparency

Privacy & Transparency