Progress Thread Project: Buried Under A Mountain Of Snow Black Hole Money Pit.

TOOLOW91 · Dec 10, 2018

srtthis said:
welp... the clecos wont hold the lower valance to the bumper. back to the drawing board.

Zeus it maybe ?

General karthief · Dec 10, 2018

Gorilla tape

srtthis · Dec 10, 2018

TOOLOW91 said:
Zeus it maybe ?

the clecos were just to hold it while the panel bond sets up. i might just re-rivet it and drill them out again.

srtthis · Dec 17, 2018

dropping the car off on the 26th to have the hatch mounted

General karthief · Dec 17, 2018

That's a funny looking hatch!

srtthis · Dec 18, 2018

General karthief said:
That's a funny looking hatch!

here is the hatch LOL

General karthief · Dec 18, 2018

Needs a cut n buff

srtthis · Dec 18, 2018

whole car needs painted lol... its not going to stay red

also needs a motor...

and a wing

and a parachute

and better brakes

srtthis · Jan 2, 2019

srtthis · Jan 14, 2019

this should help make 5 or 6 more hp
was planning on doing a soft line fogger but i couldnt pass this up for the deal i got

TOOLOW91 · Jan 14, 2019

srtthis said:
this should help make 5 or 6 more hp
was planning on doing a soft line fogger but i couldnt pass this up for the deal i got

Jets ? We don’t need no stinking jet !

srtthis · Jan 14, 2019

TOOLOW91 said:
Jets ? We don’t need no stinking jet !

haha on the stock block... its going to have jets LOL

next motor... it will have something in place where the jet goes

srtthis · Jan 21, 2019

before

still got some grinding to do but the strut tower is fixed

CarMichael Angelo · Jan 21, 2019

srtthis said:
before

still got some grinding to do but the strut tower is fixed

And why was the big hole there before?

srtthis · Jan 21, 2019

CarMichael Angelo said:
And why was the big hole there before?

when i was welding up the holes on the strut tower when i got near the top even as low as 10amp the factory sheet metal would melt away faster than i could shove filler rod in it. so i was chasing the holes it was blowing in it. ended up just saying screw it cut it out and had a friend come and mig weld it in.

srtthis · Jan 21, 2019

other stuff im in the middle of... once those panels are done ill do new brake lines

srtthis · Feb 12, 2019

like i needed another project.... other one will be here this weekend

srtthis · Feb 12, 2019

ALSO... both motors should be done in june

RangerJoe · Feb 12, 2019

srtthis said:
ALSO... both motors should be done in june

Both?

srtthis · Feb 13, 2019

RangerJoe said:
Both?

long story

but yes... have a 2nd short block at roche also

392" 14:1 NA alcohol motor

Progress Thread Project: Buried Under A Mountain Of Snow Black Hole Money Pit.

If you're the village idiot what's that make me?

Sponsors (?)

wonder how much it would cost to ship you a pair

the guy doing it does every local racers rear end

the guy doing it does every local racers rear end

Attachments

wonder how much it would cost to ship you a pair

the guy doing it does every local racers rear end

Attachments

wonder how much it would cost to ship you a pair

the guy doing it does every local racers rear end

the guy doing it does every local racers rear end

the guy doing it does every local racers rear end

If you're the village idiot what's that make me?

the guy doing it does every local racers rear end

the guy doing it does every local racers rear end

my rearend will smell so minty fresh,

the guy doing it does every local racers rear end

the guy doing it does every local racers rear end

the guy doing it does every local racers rear end

the guy doing it does every local racers rear end

I leave the horn on while driving

the guy doing it does every local racers rear end

Similar threads

Privacy & Transparency

Privacy & Transparency